OpenBSD manual page server

NAME

boot, boot.conf — macppc-specific bootstrap

DESCRIPTION

The main purpose of this program is to load the system kernel.

As described in boot_macppc(8), this program is loaded by the firmware and provides a convenient way to load the kernel. This program acts as an enhanced boot monitor for macppc systems, providing a common interface for the kernel to start from.

Basic operations include:

• Loading kernels from hard disk.
• Loading kernels compressed by gzip(1).
• Providing an interactive command line.

The sequence of its operation is as follows: initialization, parsing the configuration file, then an interactive command line. While at the command line you have 5 seconds to type any commands, if needed. If time expires, the kernel will be loaded according to the current variable settings (see the set command). If the kernel load fails, a second attempt is made with the timeout increased by one second. The sequence of boot operations is as follows:

1. If the file /etc/boot.conf exists on the filesystem in slice ‘a’ on the first disk drive (wd0), open and parse it. Lines beginning with the ‘#’ character, as well as whitespace at the beginning of lines, are ignored. The file may contain any commands boot accepts at the interactive prompt. Though default settings usually suffice, they can be changed here.
2. The header line
   >> OpenBSD/macppc BOOT [x.xx]

   is displayed to the active console, where x.xx is the version number of the boot program, followed by the

   boot>

   prompt, which means you are in interactive mode and may enter commands. If you do not, boot will proceed to load the kernel with the current parameters after the timeout period has expired.

By default, boot attempts to load the kernel executable /bsd. If it fails to find the kernel and no alternative kernel image has been specified, the system will be unable to boot.

COMMANDS

The following commands are accepted at the boot prompt:

boot [[device:]image] [-acds]

Boots the specified kernel image with any options given. If device or image are omitted, values from the boot variables will be used.

The only bootable devices, at the moment, are IDE devices connected to the internal controller; they are detected as ‘hd’ devices. Therefore, to boot kernel /bsd on the first hard drive, specify “boot hd:/bsd”.

-a

Causes the kernel to ask for the root device to use.

-c

Causes the kernel to go into boot_config(8) before performing autoconf(4) procedures.

-d

Causes the kernel to drop into ddb(4) at the earliest convenient point.

-s

Causes the kernel to boot single-user.

echo [args]

Displays args on the console device.

help

Prints a list of available commands.

hexdump addr size

Show size bytes of memory at address addr.

ls [directory]

Prints contents of the specified directory in long format including: attributes and file type, owner, group, size, filename.

reboot

Reboots the machine by initiating a warm boot procedure.

set [varname [value]]

If invoked without arguments, prints a list of variables and their values. If only varname is specified, displays contents of that variable. If varname and value are both specified, sets that variable to the given value. Variables include:

debug

Debug flag if boot was compiled with DEBUG defined.

device

Boot device name (e.g., ide, ide0, hd, hd1).

howto

Options to pass to the loaded kernel.

image

File name containing the kernel image.

timeout

Number of seconds boot will wait for human intervention before booting the default kernel image.

time

Displays system time and date.

FILES

/usr/mdec/boot

system bootstrap

/etc/boot.conf

system bootstrap's startup file

/bsd

kernel image

/bsd.rd

kernel image for installation/recovery

EXAMPLES

Boot the default kernel:

Remove the 5 second pause at boot-time permanently, causing boot to load the kernel immediately without prompting:

Boot the kernel named /bsd from the second hard disk in “User Kernel Configuration” mode (see boot_config(8)). This mechanism allows for the explicit enabling and disabling of devices during the current boot sequence, as well as the modification of device parameters. Once booted, such changes can be made permanent by using config(8)'s -e option.

SEE ALSO

gzip(1), autoconf(4), ddb(4), boot_config(8), boot_macppc(8), fdisk(8), reboot(8)

HISTORY

This program was written by Michael Shalayeff for OpenBSD 2.1 on the i386 platform, and was later ported to the macppc platform.